ansible ansible_default_ipv4 set wrong interface

user_3394220 0
Viewed 151

I am trying to configure a host and automatically select the relevant interface.
For that I am trying to run the Ansible task:

- name: Set the list of interfaces to be configured
  network_interfaces_to_configure: "{{ ansible_interfaces | difference([ ansible_default_ipv4.alias, 'lo', 'docker0' ]) }}"

For some reason it stores in network_interfaces_to_configure an interface that is deactivated — it sets it to enp1s0f1 and it should be set to enp1s0f0

The host have the following interfaces:

  • lo
  • docker0 (virtual)
  • enp1s0f0 (hardware connected and enabled)
  • enp1s0f1 (hardware disabled and without any physical connection)

I also validated that the default gateway is set to enp1s0f0.

ansible deployment linux
1 Answers

The reason why you end up with the wrong interface there is because you are excluding the correct one in your difference filter.

difference([ ansible_default_ipv4.alias, 'lo', 'docker0' ]) 
##               ^--- it is excluded because of this addition 
##                    of `ansible_default_ipv4.alias` in the list

Now, as you stated that enp1s0f1 should be excluded because it is an inactive interface, then you will have to dig further in the properties of those interfaces.

In order to do this, you have to know that the list inside ansible_interfaces, corresponds to ansible_* facts that list more information for those interfaces.

For example, in your case, you will have those facts:

  • ansible_lo
  • ansible_docker0
  • ansible_enp1s0f0
  • ansible_enp1s0f1

With information like:

ansible_lo:
  active: true
  device: lo
  ipv4:
    address: 127.0.0.1
    broadcast: ''
    netmask: 255.0.0.0
    network: 127.0.0.0
  mtu: 65536
  promisc: false
  type: loopback

So, maybe, a better idea would be to create a fact and exclude interfaces based on their active and type properties.

Something like:

- set_fact:
    active_interfaces: "{{ active_interfaces | default([]) + [item] }}"
  loop: "{{ ansible_interfaces }}"
  when: 
    ## only include active interfaces
    - lookup('vars', 'ansible_' ~ item).active
    ## exclude local loopback interfaces (`lo`)
    - lookup('vars', 'ansible_' ~ item).type != 'loopback'
    ## exclude bridge interfaces (`dockerO`)
    - lookup('vars', 'ansible_' ~ item).type != 'bridge'

Then, use that variable in network_interfaces_to_configure:

- network_interfaces_to_configure: "{{ active_interfaces }}"

Here would be an example of what this gives on my own setup, given the playbook:

- hosts: localhost
  gather_facts: yes

  tasks:
    - set_fact:
        active_interfaces: "{{ active_interfaces | default([]) + [item] }}"
      loop: "{{ ansible_interfaces }}"
      when: 
        - lookup('vars', 'ansible_' ~ item).active
        - lookup('vars', 'ansible_' ~ item).type != 'loopback'
        - lookup('vars', 'ansible_' ~ item).type != 'bridge'

    - debug:
        var: active_interfaces

This yields:

TASK [Gathering Facts] *********************************************************
ok: [localhost]

TASK [set_fact] ****************************************************************
ok: [localhost] => (item=eth0)
skipping: [localhost] => (item=tunl0) 
skipping: [localhost] => (item=docker0) 
skipping: [localhost] => (item=lo) 
ok: [localhost] => (item=services1)
skipping: [localhost] => (item=ip6tnl0) 

TASK [debug] *******************************************************************
ok: [localhost] => 
  active_interfaces:
  - eth0
  - services1
user_21235300
Related