STM32H7 SPI DMA transfer, always in busy transfer state, HAL_SPI_STATE_BUSY_TX

I am trying to transfer the data in SPI using DMA, where as my Hal status is HAL_SPI_STATUS_BUSY_TX. The required status is HAL_SPI_STATE_READY. I want to send some bulk data and command(single byte) through SPI. Is it possible to switch between DMA and non DMA mode respectively. As shown in the image, it loops in the while.

hdma1_tx.Instance                 = DMA1_Stream7;
hdma1_tx.Init.FIFOMode            = DMA_FIFOMODE_DISABLE;
hdma1_tx.Init.FIFOThreshold       = DMA_FIFO_THRESHOLD_FULL;
hdma1_tx.Init.MemBurst            = DMA_MBURST_INC4;
hdma1_tx.Init.PeriphBurst         = DMA_PBURST_INC4;
hdma1_tx.Init.Request             = DMA_REQUEST_SPI1_TX;
hdma1_tx.Init.Direction           = DMA_MEMORY_TO_PERIPH;
hdma1_tx.Init.PeriphInc           = DMA_PINC_DISABLE;
hdma1_tx.Init.MemInc              = DMA_MINC_ENABLE;
hdma1_tx.Init.PeriphDataAlignment = DMA_PDATAALIGN_BYTE;
hdma1_tx.Init.MemDataAlignment    = DMA_MDATAALIGN_BYTE;
hdma1_tx.Init.Mode                = DMA_NORMAL;
hdma1_tx.Init.Priority            = DMA_PRIORITY_LOW;

if(HAL_DMA_Init(&hdma1_tx) != HAL_OK)
{
  // Error
}

/* Associate the initialized DMA handle to the the SPI handle */
__HAL_LINKDMA(hspi, hdmatx, hdma1_tx); 

/* Configure the DMA handler for Transmission process */
hdma_rx.Instance                 = DMA1_Stream1;
hdma_rx.Init.FIFOMode            = DMA_FIFOMODE_DISABLE;
hdma_rx.Init.FIFOThreshold       = DMA_FIFO_THRESHOLD_FULL;
hdma_rx.Init.MemBurst            = DMA_MBURST_INC4;
hdma_rx.Init.PeriphBurst         = DMA_PBURST_INC4;
hdma_rx.Init.Request             = DMA_REQUEST_SPI1_RX;
hdma_rx.Init.Direction           = DMA_PERIPH_TO_MEMORY;
hdma_rx.Init.PeriphInc           = DMA_PINC_DISABLE;
hdma_rx.Init.MemInc              = DMA_MINC_ENABLE;
hdma_rx.Init.PeriphDataAlignment = DMA_PDATAALIGN_BYTE;
hdma_rx.Init.MemDataAlignment    = DMA_MDATAALIGN_BYTE;
hdma_rx.Init.Mode                = DMA_NORMAL;
hdma_rx.Init.Priority            = DMA_PRIORITY_HIGH;

HAL_DMA_Init(&hdma_rx);

/* Associate the initialized DMA handle to the the SPI handle */
__HAL_LINKDMA(hspi, hdmarx, hdma_rx);

/*##-4- Configure the NVIC for DMA #########################################*/ 
/* NVIC configuration for DMA transfer complete interrupt (SPI1_TX) */
HAL_NVIC_SetPriority(DMA1_Stream7_IRQn, 1, 1);
HAL_NVIC_EnableIRQ(DMA1_Stream7_IRQn); 

HAL_NVIC_SetPriority(SPI1_IRQn, 1, 0);
HAL_NVIC_EnableIRQ(SPI1_IRQn);

HAL_STATUS must be HAL_SPI_STATE_READY.

My data length is loaded in NDTR.

After SPI enabled NDTR = 0x00