I try to issue a scsi read(10) and write(10) to a SSD. I use this example code as a reference/basic code.
This is my scsi read:
#define READ_REPLY_LEN 32
#define READ_CMDLEN 10
void scsi_read()
{
unsigned char Readbuffer[ SCSI_OFF + READ_REPLY_LEN ];
unsigned char cmdblk [ READ_CMDLEN ] =
{ 0x28, /* command */
0, /* lun/reserved */
0, /* lba */
0, /* lba */
0, /* lba */
0, /* lba */
0, /* reserved */
0, /* transfer length */
READ_REPLY_LEN, /* transfer length */
0 };/* reserved/flag/link */
memset(Readbuffer,0,sizeof(Readbuffer));
memcpy( cmd + SCSI_OFF, cmdblk, sizeof(cmdblk) );
/*
* +------------------+
* | struct sg_header | <- cmd
* +------------------+
* | copy of cmdblk | <- cmd + SCSI_OFF
* +------------------+
*/
if (handle_scsi_cmd(sizeof(cmdblk), 0, cmd,
sizeof(Readbuffer) - SCSI_OFF, Readbuffer )) {
fprintf( stderr, "read failed\n" );
exit(2);
}
hex_dump(Readbuffer,sizeof(Readbuffer));
}
And this is my scsi write:
void scsi_write ( void )
{
unsigned char Writebuffer[SCSI_OFF];
unsigned char cmdblk [] =
{ 0x2A, /* 0: command */
0, /* 1: lun/reserved */
0, /* 2: LBA */
0, /* 3: LBA */
0, /* 4: LBA */
0, /* 5: LBA */
0, /* 6: reserved */
0, /* 7: transfer length */
0, /* 8: transfer length */
0 };/* 9: control */
memset(Writebuffer,0,sizeof(Writebuffer));
memcpy( cmd + SCSI_OFF, cmdblk, sizeof(cmdblk) );
cmd[SCSI_OFF+sizeof(cmdblk)+0] = 'A';
cmd[SCSI_OFF+sizeof(cmdblk)+1] = 'b';
cmd[SCSI_OFF+sizeof(cmdblk)+2] = 'c';
cmd[SCSI_OFF+sizeof(cmdblk)+3] = 'd';
cmd[SCSI_OFF+sizeof(cmdblk)+4] = 'e';
cmd[SCSI_OFF+sizeof(cmdblk)+5] = 'f';
cmd[SCSI_OFF+sizeof(cmdblk)+6] = 'g';
cmd[SCSI_OFF+sizeof(cmdblk)+7] = 0;
/*
* +------------------+
* | struct sg_header | <- cmd
* +------------------+
* | copy of cmdblk | <- cmd + SCSI_OFF
* +------------------+
* | data to write |
* +------------------+
*/
if (handle_scsi_cmd(sizeof(cmdblk), 8, cmd,
sizeof(Writebuffer) - SCSI_OFF, Writebuffer )) {
fprintf( stderr, "write failed\n" );
exit(2);
}
}
In the following example I do
- scsi read
- scsi write
- scsi read
And I print the hexdumps of the data which is written (scsi write) and what is read (scsi read)
Read(10)
[0000] 00 00 00 44 00 00 00 44 00 00 00 00 00 00 00 00 ...D...D ........
[0010] 00 2C 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ........ ........
[0020] 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ........ ........
[0030] 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ........ ........
[0040] 00 00 00 00 ....
Write(10):
[0000] 00 00 00 00 00 00 00 24 00 00 00 00 00 00 00 00 ........ ........
[0010] 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ........ ........
[0020] 00 00 00 00 2A 00 00 00 00 00 00 00 00 00 41 62 ........ ......Ab
[0030] 63 64 65 66 67 00 cdefg.
Read(10):
[0000] 00 00 00 44 00 00 00 44 00 00 00 00 00 00 00 00 ...D...D ........
[0010] 04 00 20 00 70 00 02 00 00 00 00 0A 00 00 00 00 ....p... ........
[0020] 04 00 00 00 41 62 63 64 65 66 67 00 00 00 00 00 ....Abcd efg.....
[0030] 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ........ ........
[0040] 00 00 00 00 ....
fter running the three commands again, I should read Abcdefg with the first read. Right? But running them again changes nothing. You could now assume, that the memory I use has still the data from previous funcions, but I get the same result even though I run memset(Readbuff,0,sizeof(Readbuff)) before the sys_read() happens.
I assumed, that the LBA I try to write is maybe forbidden to write, and I read the cache. But interating over LBA Adresses from 0x00-0xFF changes nothing - That means, I read the same data (Abcdefg).
Do you know an example implementation of scsi read or writes with the scsi generic interface?