what happened when using the same variable in two layer loops in python?

It's the same i, Python doesn't have block scope. At the beginning of each for-loop iteration, you assign the the next value in the iterator to i. Python for-loops aren't like C/Java for-loops, they are foreach loops. The continue until the iterator is exhausted (or you break out somehow). A for-loop is equivalent to the following while-loop:

iterator = iter(my_iterable)
while True:
    try:
        x = next(iterator)
    except StopIteration:
        break
    do_stuff(x)

So, your nested loop is the equivalent of this:

it1 = iter(range(3))
while True:
    try:
        i = next(it1)
    except StopIteration:
        break

    it2 = iter(range(3, 5))
    while True:
        try:
            i = next(it2)
        except StopIteration:
            break
        print "inner i: %d"%(i)

    print "outer i after: %d"%(i)

Note, a C/Java for-loop, e.g.:

for (int i = 0; i < stop; i++){
    do_stuff(i);
}

Would be in Python:

i = 0
while i < stop:
   do_stuff(i)
   i += 1

In other words, the classic-for-loop depends on i, that is, the termination condition depends on the value of i. But in a for-each loop, the termination condition depends on the iterator. And it doesn't matter what you do to the variable inside the body, at the beginning of each iteration, it is assigned the next value of the iterator.

In the inner loop you are assigning a different variable to i. Since it is the same variableit always prints 4 (the last value i was assigned in the inner loop. However, when you go to the next iteration of outer loop it will be set to the next value (i.e. 2 for the second outer loop). You should print outer loop before the inner loop to see the effect more clearly:

for i in range(3):
    print "outer i before:%d"%(i)
    for i in range(3,5):
        print "inner i: %d"%(i)
    print "outer i after: %d"%(i)

Notice how the output is always

inner i: 3
inner i: 4
outer i: 4

for every outer loop.

The program takes the final value of i in each iteration.

ie. when the outer loop starts execution, i is either 0, 1 or 2 but the value of i is modified in the inner for loop, which is getting printed.

Update:

for i in range(3):
    for i in range(3,5):
        print (id(i))
    print (id(i))

Output

1372154016
1372154032
1372154032
1372154016
1372154032
1372154032
1372154016
1372154032
1372154032

There's only one i, not two. When the inner loop is entered, it changes i, and keeps changing it until the inner loop exits. The next iteration of the outer loop then sets i to the next value in its range, but you never see it because you immediately enter the inner loop once more, again changing i.

This is of course very bad practice. You should never modify the variable in a for loop while that loop is active.

Its the same i being used in both loops. When the outer loops gets a chance to print i, it will always have the last assigned value from the inner loop.

Check @heltonbiker answer :

>>> for i in range(3):
    print "1-",locals()
    for i in range(3,5):
        print "2-",locals()


1- {'__builtins__': <module '__builtin__' (built-in)>, '__package__': None, 'i': 0, '__name__': '__main__', '__doc__': None}
2- {'__builtins__': <module '__builtin__' (built-in)>, '__package__': None, 'i': 3, '__name__': '__main__', '__doc__': None}
2- {'__builtins__': <module '__builtin__' (built-in)>, '__package__': None, 'i': 4, '__name__': '__main__', '__doc__': None}
1- {'__builtins__': <module '__builtin__' (built-in)>, '__package__': None, 'i': 1, '__name__': '__main__', '__doc__': None}
2- {'__builtins__': <module '__builtin__' (built-in)>, '__package__': None, 'i': 3, '__name__': '__main__', '__doc__': None}
2- {'__builtins__': <module '__builtin__' (built-in)>, '__package__': None, 'i': 4, '__name__': '__main__', '__doc__': None}
1- {'__builtins__': <module '__builtin__' (built-in)>, '__package__': None, 'i': 2, '__name__': '__main__', '__doc__': None}
2- {'__builtins__': <module '__builtin__' (built-in)>, '__package__': None, 'i': 3, '__name__': '__main__', '__doc__': None}
2- {'__builtins__': <module '__builtin__' (built-in)>, '__package__': None, 'i': 4, '__name__': '__main__', '__doc__': None}
>>> 

You read i data on wrong time (place)!

If there is a single BUS or Variable name You must use the FIFO method.

FIFO << Here information